Home > technological innovation

Metal Mould in the stamping process Note that security matters

Dongguan City, Kang Ding Metal Products Co., Ltd. is the Pearl River Delta of the most professional precision metal stamping factory.

Our metal stamping punch punching speed is generally 800-1000 beats / min.
1, metal shrapnel material used:
   
When the production of metal shrapnel, and to select appropriate materials normally can not be seen on the selection of cheaper. Each material can also be separated in several different small materials, but many manufacturers produce what materials can be separated out of the product is high quality. So we buy metal shrapnel time to note the material it uses.
   
2, metal shrapnel efforts:
 
Many foreign customers is the strength of metal shrapnel requirements are very strict, that we use metal shrapnel efforts should be uniform, one high and one low-intensity situation can not arise, of course we can be controlled to a certain intensity tolerance ( within ± 20gf) range.
 
3, metal shrapnel of life:
 
At present a lot of metal shrapnel life simply not up to standard, although the price is relatively much cheaper, but we buy metal shrapnel are not due to greedy one into the cheap to buy inferior metal shrapnel, so when we buy metal shrapnel Note that it can be used by life
Metal shrapnel die in the stamping process, the use of high-speed presses, the risk coefficient is relatively high. If done incorrectly, it can cause serious damage to the mold, and the safety of operating personnel will be hurt, so die to be under the machine, remember to perform the following operations in order to ensure the safety of molds and operating personnel.

Metal shrapnel die in the stamping process, the use of high-speed presses, the risk coefficient is relatively high. If done incorrectly, it can cause serious damage to the mold, and the safety of operating personnel will be hurt, so die to be under the machine, remember to perform the following operations in order to ensure the safety of molds and operating personnel.
Metal shrapnel die under the machine two cases, under normal and abnormal machine under the machine.
First, under normal Mould Machine:
1. The first punch hit "inching", turn off the counter;
2. Use the jog switch to punch hit bottom dead center (180 °), cut the strip; the strip cut when the mold is prohibited without the lower dead point, easily lead to deformation of the strip and mold parts damage.
3. Loosen the upper and lower mold screws.
4. The punch hit the dead, while the mold is pulled mold car center position, when they both die required to complete, a person can not pull the mold in order to ensure safety.
5. The mold car must be pulled before the lower mold car some distance away from the height after punch. Prevent mold car stuck in the punch platform, resulting in mold slide.
6. The clamping screws, scissors, hook material, flashlights and other prohibited when the mold is placed on the lower mold presses the operation surface platform.
Second, Mould exception under machine:
1. Turn off the host power supply and counter;
2. flywheel be completely stopped using plastic or paper hearts stop high column placed diagonally around the mold. Non-pad on the strip between the feed plate and the mold core fixed plate, nor the available iron instead of plastic into a mold.
3. Shake the flywheel with safety bar (avoid pulling the flywheel or the flywheel by hand before using the safety bar to prevent the flywheel not stop running) up and down the stick to stop high column.
4. Loosen the screw up and down mode, with a safety bar to pull the flywheel to 0 ° ~ 70 °, the mold can be pulled down.
Third, the lower metal mold machine Note:
1. Pull the mold to be confirmed before the mold inlet strip pallets have loose win.
2. Mold pull them out when one person can pull, push one back. (Should not they both pushed back the launch punch mold platform) can also be used to lift mold screw holes after circling the lower die, his hands lifted up a little while later pulled out.
3. pull away from the punch die mold can not turn the car too fast, to prevent guide plate or material pallets caught punch or punch enclosures, causing damage or mold mold parts slide.
The exception under the mold when no longer jog operation, especially after the high column pad plastic mold stopper.
5. The mold lower die will punch the host and other power off and avoid wasting resources.
6. Mold normal shutdown need to mold jog operation to guide the needle into the material with a hole. (To prevent material feeder not holding material without causing back pressure caused by the tapes.) Do not stop at the dead mold point. (Easily lead to reduced service life of the spring within the mold)


Dongguan Kang Ding precision metal processing using advanced equipment, product quality assurance, fast delivery, reasonable prices, the industry-leadingby foreign customers trust and love. !

Welcome13827205356 Mr Chan

CONTACT US

Contact: Kevin Chen

Phone: (+86)13827205356

Tel: (+86)769-83811196

Email: cnc@cncstamping.com

Add: No. 51 Luming Road Heavy River Management District - Qing Town Dongguan City